Forum Debian Users Gang

morfik · 2023-04-03 11:03:22

Ostatnio migruję swoją kolekcję mp3 na nieskompresowany format flac. Pliki mp3 miały 16bit/44,1KHz, a te flac mają 24bit/96KHz. Z tego co kiedyś czytałem, to nie każdy sprzęt jest w stanie taki format muzyki odtwarzać. Więc pytania są dwa, jak sprawdzić czy dana karta dźwiękowa wspiera 24bit/96KHz i jak skonfigurować system do pracy z takimi plikami?

Karta to:

Kod:

# cat /proc/asound/cards
 0 [PCH            ]: HDA-Intel - HDA Intel PCH
                      HDA Intel PCH at 0xe1530000 irq 31

Kod:

$ lspci -vnn

00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C216 Chipset Family High Definition Audio Controller [8086:1e20] (rev 04)
        Subsystem: Lenovo 7 Series/C216 Chipset Family High Definition Audio Controller [17aa:21f3]
        Flags: bus master, fast devsel, latency 0, IRQ 31, IOMMU group 5
        Memory at e1530000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: <access denied>
        Kernel driver in use: snd_hda_intel

W konfiguracji pulseaudio (/etc/pulse/daemon.conf) jest niby do ustawienia:

Kod:

default-sample-format = s24le
default-sample-rate = 44100
alternate-sample-rate = 96000

I niby gra ale tutaj zamiast 24bit jest 32 bit:

Kod:

$ pactl list sinks
Sink #0
        State: RUNNING
        Name: alsa_output.pci-0000_00_1b.0.analog-stereo
        Description: Built-in Audio Analog Stereo
        Driver: module-alsa-card.c
        Sample Specification: s32le 2ch 96000Hz
        Channel Map: front-left,front-right
        Owner Module: 6
        Mute: no
        Volume: front-left: 16384 /  25% / -36.12 dB,   front-right: 16384 /  25% / -36.12 dB
                balance 0.00
        Base Volume: 65536 / 100% / 0.00 dB
        Monitor Source: alsa_output.pci-0000_00_1b.0.analog-stereo.monitor
        Latency: 89355 usec, configured 90000 usec
        Flags: HARDWARE HW_MUTE_CTRL HW_VOLUME_CTRL DECIBEL_VOLUME LATENCY
        Properties:
                alsa.resolution_bits = "32"
                device.api = "alsa"
                device.class = "sound"
                alsa.class = "generic"
                alsa.subclass = "generic-mix"
                alsa.name = "ALC3202 Analog"
                alsa.id = "ALC3202 Analog"
                alsa.subdevice = "0"
                alsa.subdevice_name = "subdevice #0"
                alsa.device = "0"
                alsa.card = "0"
                alsa.card_name = "HDA Intel PCH"
                alsa.long_card_name = "HDA Intel PCH at 0xe1530000 irq 31"
                device.bus_path = "pci-0000:00:1b.0"
                sysfs.path = "/devices/pci0000:00/0000:00:1b.0/sound/card0"
                device.bus = "pci"
                device.vendor.id = "8086"
                device.vendor.name = "Intel Corporation"
                device.product.id = "1e20"
                device.product.name = "7 Series/C216 Chipset Family High Definition Audio Controller"
                device.form_factor = "internal"
                device.string = "front:0"
                device.buffering.buffer_size = "705600"
                device.buffering.fragment_size = "352800"
                device.access_mode = "mmap+timer"
                device.profile.name = "analog-stereo"
                device.profile.description = "Analog Stereo"
                device.description = "Built-in Audio Analog Stereo"
                module-udev-detect.discovered = "1"
                device.icon_name = "audio-card-pci"
        Ports:
                analog-output-speaker: Speakers (type: Speaker, priority: 10000, not available)
                analog-output-headphones: Headphones (type: Headphones, priority: 9900, available)
        Active Port: analog-output-headphones
        Formats:
                pcm

Jak się popatrzy w /proc/asound/card0/pcm0p/sub0/hw_params , to podczas odtwarzania mp3 jest:

Kod:

$ cat /proc/asound/card0/pcm0p/sub0/hw_params
access: MMAP_INTERLEAVED
format: S32_LE
subformat: STD
channels: 2
rate: 44100 (44100/1)
period_size: 44100
buffer_size: 88200

A podczas odtwarzania flac:

Kod:

$ cat /proc/asound/card0/pcm0p/sub0/hw_params
access: MMAP_INTERLEAVED
format: S32_LE
subformat: STD
channels: 2
rate: 96000 (96000/1)
period_size: 44100
buffer_size: 88200

Czy to tak ma wyglądać, czy coś tam w konfiguracji PA trzeba jeszcze ustawić? Czy period_size i
buffer_size w przypadku flac powinny mieć takie same wartości co w przypadku mp3 czy trzeba je zwiększyć i gdzie to zrobić, bo w konfiguracji PA nie widzę takich opcji.

Znalazłem też info, że:

# The default sample frequency. PulseAudio supports any sample rate between 1 Hz and 192000 Hz,
# usually 32000, 44100, 48000, 88200, 96000, 176400, 192000. There is no point trying to exceed the
# sample rate of the output device though as the signal will only get downsampled, consuming CPU on
# the machine running the server.

Więc jak zweryfikować, czy ta karta dźwiękowa albo system nie będą mieć problemów z powodu tego flac'a?

Rafcio6179 · 2023-04-03 12:52:22

Z odtwarzaniem flac'a powinien poradzić sobie odtwarzacz DeaDBeeF. Jeżeli zależy Tobie na poprawieniu jakości dźwięku z komputera, to powtórnym konwertowaniem na format bezstratny tego nie uzyskasz.
Używam zewnętrznego 24 bitowego przetwornika DacMagic100 od Cambridge Audio, który współpracuje z Asio i foobarem.
Debian radzi sobie z obsługą tego DACa, ale wiąże się to z zakupem przetwornika, który nie jest tani.

morfik · 2023-04-03 13:04:32

Tzn, te flac'i są nowymi plikami i nie mają nic wspólnego ze starymi plikami mp3, poza oczywiście nazwą utworu, itp. xD

Strawberry zdaje sobie radzić z odtwarzaniem, i info, które zwraca przy odtwarzanym kawałku jest poprawne (te 24bit/96KHz i zmienny bitrate około 2200kbit/s).

Jacekalex · 2023-04-04 10:45:13

@Morfik

Masz może jak podrzucić takiego flacka lub napisz, jak go wygenerować w 24b@96000, to zobaczę u siebie na:

Kod:

Ciąg serwera: /run/user/1000/pulse/native
Wersja protokołu biblioteki: 35
Wersja protokołu serwera: 35
Czy jest lokalny: tak
Indeks klienta: 72
Rozmiar kafla: 65472
Nazwa użytkownika: pacjent
Nazwa komputera: domek
Nazwa serwera: PulseAudio (on PipeWire 0.3.66)
Wersja serwera: 15.0.0
Domyślne określenie próbki: float32le 2 k 192000 Hz
Domyślna mapa kanałów: front-left,front-right
Domyślny odpływ: alsa_output.pci-0000_00_1b.0.analog-surround-21
Domyślne źródło: alsa_output.pci-0000_00_1b.0.analog-surround-21.monitor
Ciasteczko: 5cd0:2681

Ostatnio edytowany przez Jacekalex (2023-04-04 10:45:30)

morfik · 2023-04-04 11:32:00

Zgodnie z tym co piszą tutaj, wrzuciłem do /etc/pulse/default.pa:

Kod:

load-module module-udev-detect tsched=0

i do /etc/pulse/daemon.conf :

Kod:

default-fragments = 3
default-fragment-size-msec = 5

I teraz jest:

Kod:

# cat /proc/asound/card0/pcm0p/sub0/hw_params
access: MMAP_INTERLEAVED
format: S32_LE
subformat: STD
channels: 2
rate: 96000 (96000/1)
period_size: 220
buffer_size: 660

Bufor i okres znacząco się obniżyły ale to chyba przy piosenkach nie ma większego znaczenia. xD

Ostatnio edytowany przez morfik (2023-04-04 11:36:55)

Jacekalex · 2023-04-04 11:36:06

Kod:

# root ~> egrep -v '#|^$' /etc/pipewire/pipewire.conf 
context.properties = {
    default.clock.rate          = 192000
    default.clock.allowed-rates = [ 48000 44100 96000 192000]
    default.clock.min-quantum   = 16
    vm.overrides = {
        default.clock.min-quantum = 1024
    }
}
context.spa-libs = {
    audio.convert.* = audioconvert/libspa-audioconvert
    api.alsa.*      = alsa/libspa-alsa
    api.v4l2.*      = v4l2/libspa-v4l2
    api.libcamera.* = libcamera/libspa-libcamera
    api.vulkan.*    = vulkan/libspa-vulkan
    api.jack.*      = jack/libspa-jack
    support.*       = support/libspa-support
}
context.modules = [
    { name = libpipewire-module-rt
        args = {
            nice.level    = -11
        }
        flags = [ ifexists nofail ]
    }
    { name = libpipewire-module-protocol-native }
    { name = libpipewire-module-profiler }
    { name = libpipewire-module-metadata }
    { name = libpipewire-module-spa-device-factory }
    { name = libpipewire-module-spa-node-factory }
    { name = libpipewire-module-client-node }
    { name = libpipewire-module-client-device }
    { name = libpipewire-module-portal
        flags = [ ifexists nofail ]
    }
    { name = libpipewire-module-access
        args = {
        }
    }
    { name = libpipewire-module-adapter }
    { name = libpipewire-module-link-factory }
    { name = libpipewire-module-session-manager }
]
context.objects = [
    { factory = spa-node-factory
        args = {
            factory.name    = support.node.driver
            node.name       = Dummy-Driver
            node.group      = pipewire.dummy
            priority.driver = 20000
        }
    }
    { factory = spa-node-factory
        args = {
            factory.name    = support.node.driver
            node.name       = Freewheel-Driver
            priority.driver = 19000
            node.group      = pipewire.freewheel
            node.freewheel  = true
        }
    }
            api.alsa.period-size   = 8192
]
context.exec = [
]

morfik · 2023-04-04 11:38:59

A jak ręcznie ustalić jakie karta dźwiękowa ma parametry, tak by dobrać wartości pod konkretny sprzęt?

Jacekalex · 2023-04-04 11:41:56

morfik napisał(-a):
A jak ręcznie ustalić jakie karta dźwiękowa ma parametry, tak by dobrać wartości pod konkretny sprzęt?

Kod:

### cat  /proc/asound/card1/codec#2 
Codec: Realtek ALC1150
Address: 2
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x10ec0900
Subsystem Id: 0x1458a182
Revision Id: 0x100001
No Modem Function Group found
Default PCM:
    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
  Power states:  D0 D1 D2 D3 CLKSTOP EPSS
  Power: setting=D0, actual=D0
GPIO: io=2, o=0, i=0, unsolicited=1, wake=0
  IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
  IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Node 0x02 [Audio Output] wcaps 0x41d: Stereo Amp-Out
  Control: name="Front Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Device: name="ALC1150 Analog", type="Audio", device=0
  Amp-Out caps: ofs=0x57, nsteps=0x57, stepsize=0x02, mute=0
  Amp-Out vals:  [0x57 0x57]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x41d: Stereo Amp-Out
  Control: name="Surround Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x57, nsteps=0x57, stepsize=0x02, mute=0
  Amp-Out vals:  [0x57 0x57]
  Converter: stream=5, channel=2
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
Node 0x04 [Audio Output] wcaps 0x41d: Stereo Amp-Out
  Control: name="Center Playback Volume", index=0, device=0
    ControlAmp: chs=1, dir=Out, idx=0, ofs=0
  Control: name="LFE Playback Volume", index=0, device=0
    ControlAmp: chs=2, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x57, nsteps=0x57, stepsize=0x02, mute=0
  Amp-Out vals:  [0x57 0x57]
  Converter: stream=5, channel=4
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
Node 0x05 [Audio Output] wcaps 0x41d: Stereo Amp-Out
  Control: name="Side Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x57, nsteps=0x57, stepsize=0x02, mute=0
  Amp-Out vals:  [0x57 0x57]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
Node 0x06 [Audio Output] wcaps 0x611: Stereo Digital
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  IEC Coding Type: 0x0
  PCM:
    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
Node 0x07 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x08 [Audio Input] wcaps 0x10051b: Stereo Amp-In
  Control: name="Capture Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Capture Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Device: name="ALC1150 Analog", type="Audio", device=0
  Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
  Amp-In vals:  [0x3f 0x3f]
  Converter: stream=0, channel=0
  SDI-Select: 0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x23
Node 0x09 [Audio Input] wcaps 0x10051b: Stereo Amp-In
  Control: name="Capture Volume", index=1, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Capture Switch", index=1, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Device: name="ALC1150 Alt Analog", type="Audio", device=2
  Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
  Amp-In vals:  [0xbf 0xbf]
  Converter: stream=1, channel=0
  SDI-Select: 0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x22
Node 0x0a [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x0b [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Control: name="Front Mic Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=1, ofs=0
  Control: name="Front Mic Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=1, ofs=0
  Control: name="Rear Mic Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Rear Mic Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Line Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=2, ofs=0
  Control: name="Line Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=2, ofs=0
  Control: name="Beep Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=5, ofs=0
  Control: name="Beep Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=5, ofs=0
  Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1
  Amp-In vals:  [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
  Connection: 8
     0x18 0x19 0x1a 0x1b 0x14 0x15 0x16 0x17
Node 0x0c [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-In vals:  [0x00 0x00] [0x80 0x80]
  Connection: 2
     0x02 0x0b
Node 0x0d [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-In vals:  [0x00 0x00] [0x80 0x80]
  Connection: 2
     0x03 0x0b
Node 0x0e [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-In vals:  [0x00 0x00] [0x80 0x80]
  Connection: 2
     0x04 0x0b
Node 0x0f [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-In vals:  [0x00 0x00] [0x80 0x80]
  Connection: 2
     0x05 0x0b
Node 0x10 [Audio Output] wcaps 0x611: Stereo Digital
  Control: name="IEC958 Playback Con Mask", index=0, device=0
  Control: name="IEC958 Playback Pro Mask", index=0, device=0
  Control: name="IEC958 Playback Default", index=0, device=0
  Control: name="IEC958 Playback Switch", index=0, device=0
  Control: name="IEC958 Default PCM Playback Switch", index=0, device=0
  Device: name="ALC1150 Digital", type="SPDIF", device=1
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  IEC Coding Type: 0x0
  PCM:
    rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
Node 0x11 [Pin Complex] wcaps 0x400781: Stereo Digital
  Pincap 0x00000014: OUT Detect
  Pin Default 0x99430130: [Fixed] SPDIF Out at Int ATAPI
    Conn = ATAPI, Color = Unknown
    DefAssociation = 0x3, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x10
Node 0x12 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x13 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
  Control: name="Front Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x0001003e: IN OUT HP EAPD Detect Trigger
  EAPD 0x2: EAPD
  Pin Default 0x01014010: [Jack] Line Out at Ext Rear
    Conn = 1/8, Color = Green
    DefAssociation = 0x1, Sequence = 0x0
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=05, enabled=1
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x0c
Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
  Control: name="Surround Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x00000036: IN OUT Detect Trigger
  Pin Default 0x01011012: [Jack] Line Out at Ext Rear
    Conn = 1/8, Color = Black
    DefAssociation = 0x1, Sequence = 0x2
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=06, enabled=1
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x0d
Node 0x16 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
  Control: name="Center Playback Switch", index=0, device=0
    ControlAmp: chs=1, dir=Out, idx=0, ofs=0
  Control: name="LFE Playback Switch", index=0, device=0
    ControlAmp: chs=2, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x00000036: IN OUT Detect Trigger
  Pin Default 0x01016011: [Jack] Line Out at Ext Rear
    Conn = 1/8, Color = Orange
    DefAssociation = 0x1, Sequence = 0x1
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=07, enabled=1
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x0e
Node 0x17 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
  Control: name="Side Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x00000036: IN OUT Detect Trigger
  Pin Default 0x01012014: [Jack] Line Out at Ext Rear
    Conn = 1/8, Color = Grey
    DefAssociation = 0x1, Sequence = 0x4
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=08, enabled=1
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x0f
Node 0x18 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Rear Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x80 0x80]
  Pincap 0x00003736: IN OUT Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x01a19040: [Jack] Mic at Ext Rear
    Conn = 1/8, Color = Pink
    DefAssociation = 0x4, Sequence = 0x0
  Pin-ctls: 0x24: IN VREF_80
  Unsolicited: tag=03, enabled=1
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x19 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Front Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x03 0x03]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x80 0x80]
  Pincap 0x0000373e: IN OUT HP Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x02a19050: [Jack] Mic at Ext Front
    Conn = 1/8, Color = Pink
    DefAssociation = 0x5, Sequence = 0x0
  Pin-ctls: 0x24: IN VREF_80
  Unsolicited: tag=02, enabled=1
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x1a [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Line Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x80 0x80]
  Pincap 0x00003736: IN OUT Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  Pin Default 0x0181304f: [Jack] Line In at Ext Rear
    Conn = 1/8, Color = Blue
    DefAssociation = 0x4, Sequence = 0xf
  Pin-ctls: 0x20: IN VREF_HIZ
  Unsolicited: tag=04, enabled=1
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x1b [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
  Control: name="Headphone Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-In vals:  [0x00 0x00]
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x80 0x80]
  Pincap 0x0001373e: IN OUT HP EAPD Detect Trigger
    Vref caps: HIZ 50 GRD 80 100
  EAPD 0x2: EAPD
  Pin Default 0x02214020: [Jack] HP Out at Ext Front
    Conn = 1/8, Color = Green
    DefAssociation = 0x2, Sequence = 0x0
  Pin-ctls: 0xc0: OUT HP VREF_HIZ
  Unsolicited: tag=01, enabled=1
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 5
     0x0c 0x0d 0x0e 0x0f 0x26*
Node 0x1c [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x1d [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x1e [Pin Complex] wcaps 0x400781: Stereo Digital
  Pincap 0x00000014: OUT Detect
  Pin Default 0x4037d500: [N/A] CD at Ext N/A
    Conn = Analog, Color = UNKNOWN
    DefAssociation = 0x0, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x06
Node 0x1f [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono
  Processing caps: benign=0, ncoeff=32
Node 0x21 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x22 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-In vals:  [0x80 0x80] [0x00 0x00] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
  Connection: 9
     0x18 0x19 0x1a 0x1b 0x14 0x15 0x16 0x17 0x0b
Node 0x23 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-In vals:  [0x80 0x80] [0x00 0x00] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
  Connection: 9
     0x18 0x19 0x1a 0x1b 0x14 0x15 0x16 0x17 0x0b
Node 0x24 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x25 [Audio Output] wcaps 0x41d: Stereo Amp-Out
  Control: name="Headphone Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x57, nsteps=0x57, stepsize=0x02, mute=0
  Amp-Out vals:  [0x00 0x00]
  Converter: stream=5, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 EPSS
  Power: setting=D0, actual=D0
Node 0x26 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-In vals:  [0x00 0x00] [0x80 0x80]
  Connection: 2
     0x25 0x0b

Jak widać, informacje są na swoim miejscu.
xD

morfik · 2023-04-04 11:46:26

Dużo tych informacji. xD

Ale wygląda na to, że

Kod:

rates [0x5f0]: 32000 44100 48000 88200 96000 192000
    bits [0xe]: 16 20 24

już chyba wszędzie jest i te karty powinny działać dobrze z takimi plikami flac.

Forum Debian Users Gang

Ogłoszenie

#1 2023-04-03 11:03:22

morfik - Cenzor wirtualnego świata

Muzyka w 24bit/96KHz

Kod:

Kod:

Kod:

Kod:

Kod:

Kod:

#2 2023-04-03 12:52:22

Rafcio6179 - Użytkownik

Re: Muzyka w 24bit/96KHz

#3 2023-04-03 13:04:32

morfik - Cenzor wirtualnego świata

Re: Muzyka w 24bit/96KHz

#4 2023-04-04 10:45:13

Jacekalex - Podobno człowiek...;)

Re: Muzyka w 24bit/96KHz

Kod:

#5 2023-04-04 11:32:00

morfik - Cenzor wirtualnego świata

Re: Muzyka w 24bit/96KHz

Kod:

Kod:

Kod:

#6 2023-04-04 11:36:06

Jacekalex - Podobno człowiek...;)

Re: Muzyka w 24bit/96KHz

Kod:

#7 2023-04-04 11:38:59

morfik - Cenzor wirtualnego świata

Re: Muzyka w 24bit/96KHz

#8 2023-04-04 11:41:56

Jacekalex - Podobno człowiek...;)

Re: Muzyka w 24bit/96KHz

morfik napisał(-a):

Kod:

#9 2023-04-04 11:46:26

morfik - Cenzor wirtualnego świata

Re: Muzyka w 24bit/96KHz

Kod:

Stopka forum