Forum Debian Users Gang

Mam kłopot z podłączeniem do debiana komórki Siemensa kablem usb.
Po wpisaniu:
# lsusb
Bus 001 Device 001: ID 0000:0000
Bus 001 Device 003: ID 11f5:0003 Siemens AG (?) Mobile phone USB cable

w usbview:
Siemens USB Connectivity jest na czerwono

moduły:
Module Size Used by Not tainted
apm 8428 1 (autoclean)
pcmcia_core 38020 0
parport_pc 19432 1 (autoclean)
lp 5540 0
parport 21608 1 [parport_pc lp]
mousedev 3604 0 (unused)
hid 19076 0 (unused)
af_packet 11048 1 (autoclean)
usb-uhci 19504 0 (unused)
snd-emu10k1 62308 0
snd-pcm-oss 34048 0 (unused)
snd-mixer-oss 11000 0 [snd-pcm-oss]
snd-hwdep 4128 0 [snd-emu10k1]
snd-util-mem 1056 0 [snd-emu10k1]
snd-ac97-codec 48280 0 [snd-emu10k1]
snd-pcm 50216 0 [snd-emu10k1 snd-pcm-oss snd-ac97-codec]
snd-timer 12548 0 [snd-emu10k1 snd-pcm]
snd-rawmidi 11552 0 [snd-emu10k1]
snd-seq-device 3588 0 [snd-emu10k1 snd-rawmidi]
snd 28260 0 [snd-emu10k1 snd-pcm-oss snd-mixer-oss snd-hwdep snd-util-mem snd-ac97-codec snd-pcm snd-timer snd-rawmidi snd-seq-device]
soundcore 3268 8 [snd]
snd-page-alloc 4296 0 [snd-emu10k1 snd-mixer-oss snd-hwdep snd-pcm snd-timer snd-rawmidi snd-seq-device snd]
ide-scsi 8272 0
scsi_mod 86020 1 [ide-scsi]
8139too 12328 1
mii 1952 0 [8139too]
crc32 2848 0 [8139too]
i810_rng 2368 0 (unused)
agpgart 39108 4
visor 10664 0 (unused)
fuse 16732 0
hci_usb 7352 0 (unused)
bluez 24580 0 [hci_usb]
irda 123200 0 (unused)
pl2303 9784 0 (unused)
usbserial 18204 0 [visor pl2303]
usbcore 52268 1 [hid usb-uhci visor hci_usb pl2303 usbserial]
phonedev 2464 0 (unused)
keybdev 1732 0 (unused)
input 3040 0 [mousedev hid keybdev]
ide-cd 27040 0
cdrom 26212 0 [ide-cd]
rtc 5768 0 (autoclean)
ext3 65388 1 (autoclean)
jbd 34628 1 (autoclean) [ext3]
ide-detect 288 0 (autoclean) (unused)
piix 7784 1 (autoclean)
ide-disk 12416 2 (autoclean)
ide-core 91800 2 (autoclean) [ide-scsi ide-cd ide-detect piix ide-disk]
unix 12752 196 (autoclean)

po wpisaniu dmesg usb końcówka wygląda tak:
usb.c: USB disconnect on device 00:1f.2-2 address 2
hub.c: new USB device 00:1f.2-2, assigned address 3
usb.c: USB device 3 (vend/prod 0x11f5/0x3) is not claimed by any active driver.

a po wpisaniu:
# pager /proc/bus/usb/devices

T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=d000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=32 #Cfgs= 1
P: Vendor=11f5 ProdID=0003 Rev= 0.95
S: Manufacturer=Siemens AG
S: Product=Siemens USB Connectivity
S: SerialNumber= 353538004664670
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 98mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=04 Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 2 Ivl=4ms

prosze o pomoc